Analog input channels

MSO22: 2 channel

MSO24: 4 channel

Input coupling

AC, DC

Input termination selection

1 MΩ only

Input termination, 1 MΩ DC-coupled

1 MΩ ± 1%

Input capacitance, 1 MΩ DC-coupled

14 pF ± 3 pF

Digitized bits

8 bits

Displayed vertically with 25 digitization levels (DL) per division, 10.24 divisions dynamic range. A converter can resolve the smallest voltage level change by using an 8-bit A–D converter. This value is also known as the Least Significant Bit (LSB).

Sensitivity range (coarse), 1 MΩ

1 mV/Div to 10 V/Div in a 1-2-5 sequence

Sensitivity range (fine)

Continuous adjustment from 1 mV/DIV to 10 V/DIV, 1 MΩ 1x

Sensitivity resolution (fine)

≤10% of current setting

Maximum input voltage, 1 MΩ DC-coupled

Maximum input voltage at the BNC, 300 V_rms. Installation category II

Derate at 20 dB/decade between 3 MHz to 30 MHz

Derate at 15.5 dB between 30 MHz to 300 MHz; above 300 MHz, 5 V_rms

Maximum peak input voltage at the BNC: ± 424 V

✔ DC gain accuracy

Guaranteed for 2 mV/div and above, typical otherwise. Specification valid after 30 minute warm-up and Signal Path Compensation (SPC) at ambient.

<2 mV/div: ±3.0%, typical, derated at 0.100%/°C above 30 °C

≥2 mV/div: ±2.0%, derated at 0.100%/°C above 30 °C

Offset ranges

1 mV/div to 63.8 mV/div : ±1 V

63.9 mV/div to 999.5 mV/div : ±10 V

1 V/div to 10 V/div : ±100 V

Position range

±5 divisions

Offset accuracy

All terms must be converted to volts by multiplying by the current volts/div setting.

>2 mV/div: ± (0.005 X |offset – position | + 0.2 div)

≤2 mV/div: ± (0.005 X |offset – position | + 0.3 div)

Waveforms for average acquisition mode

2 to 10.24 k waveforms; default of 16 waveforms

DC voltage measurement accuracy, average acquisition mode

The basic accuracy specification applies directly to any sample and to the following measurements: high, low, maximum, minimum, mean, cycle mean, RMS, and cycle RMS. The delta volts accuracy specification applies to subtractive calculations involving two of these measurements. The delta volts (difference voltage) accuracy specification applies directly to the following measurements; positive overshoot, negative overshoot, Pk-Pk, and amplitude.

Offset, position, and the constant offset term must be converted to volts by multiplying by the appropriate volts/div term.

The limits are as follows:

Measurement type	DC accuracy (in volts)
Average of > 16 waveforms	± ((DC Gain accuracy) X |reading -(offset - position)| + Offset accuracy + 0.1 div + 1 mV)
Delta volts between any two averages of ≥16 waveforms acquired with the same oscilloscope setup and ambient conditions	± (DC Gain accuracy X |reading| + 0.08 div + 1.4 mV)

Bandwidth selections

20 MHz, 70 MHz, 100 MHz, 200 MHz, 350 MHz, and 500 MHz (when equal to or less than instrument's rated bandwidth)

✔ Analog bandwidth

Below 5 mV/div, 500 MHz bandwidth is specified as typical.

The limits stated below are for an ambient temperature of ≤30 °C. For each degree above 30 °C, reduce the upper bandwidth frequency by 1%.

Instrument bandwidth	Volts/div setting	Bandwidth
70 MHz	1 mV/div – 10 V/div	DC – 70 MHz
100 MHz	1 mV/div – 10 V/div	DC – 100 MHz
200 MHz	1 mV/div – 10 V/div	DC – 200 MHz
350 MHz	1 mV/div – 10 V/div	DC – 350 MHz
500 MHz	<5 mV/div	DC – 500 MHz
500 MHz	≥5 mV/div - 10 V/div	DC – 500 MHz

Lower frequency limit, AC-coupled

<10 Hz

The AC-coupled lower frequency limits are reduced by a factor of 10 (<1 Hz) when 10X passive probes are used.

Upper frequency limit, 20 MHz bandwidth-limited

20 MHz, ± 25%, DC-coupled

Calculated rise time

Measurements made using the oscilloscope's automated measurement feature may read slower rise time values than those determined by the above equation. This is because the automated measurements do not take interpolation into account. Measuring using cursors on the interpolated waveform gives a more accurate result.

The formula is calculated by measuring the –3 dB bandwidth of the oscilloscope. The formula accounts for the rise time contribution of the oscilloscope independent of the rise time of the signal source.

Calculated rise time (10% to 90%, in ps) equals 0.35/BW except from 1000 to 2100 mentioned in below table.

Bandwidth	Rise time (ps)
500 MHz	1000
350 MHz	1400
200 MHz	2100
100 MHz	3500
70 MHz	5000

Peak detect or envelope mode pulse response

Peak detect response indicates how effective the oscilloscope is at picking up a single narrow pulse and determining its amplitude.

The minimum single pulse widths for peak detect or envelope mode is at least:

Bandwidth (MHz)	Minimum pulse width
500	> 2 ns
350	> 3 ns
200	> 5 ns
100	> 10 ns
70	> 14 ns
50	> 20 ns

Deskew range

-95 ns to +95 ns

Crosstalk (channel isolation)

	≤ 100 MHz	> 100 MHz
1 MΩ	100:1	30:1

Sample rate range

Maximum 1.25 GS/s - All channels

Maximum 2.5 GS/s - Half channel

Record length range

10 M Standard

Seconds/Division range

1 ns/div to 1000 s/div when in half channel mode

2 ns/div to 1000 s/div when in full channel mode

Maximum triggered acquisition rate

>5k wfm/s

✔ Timebase accuracy

± 25 x 10^-6 over any over any ≥1 ms interval

Guaranteed, the specification valid after 30 minute warm-up and Signal Path Compensation (SPC) at ambient.

Timebase delay time range

-10 divisions to 5000 s

Delta time measurement accuracy (DTA)

The formula to calculate delta-time measurement accuracy (DTA) for a given instrument setting and input signal is as follows (assumes insignificant signal content above the Nyquist frequency).

SR₁ = Slew rate (1^st Edge) around 1^st point in measurement

SR₂ = Slew rate (2^nd Edge) around 2^nd point in measurement

N = Input-referred noise (V_rms)

TBA = Timebase accuracy

tp = Delta-time measurement duration (sec)

RD = (Record length)/(Sample rate)

(assume edge shape that results from Gaussian filter response)

(Assumes insignificant error due to aliasing)

The term under the square root sign is stability and is due to Time Interval Error (TIE). The errors due to this term occur throughout a single-shot measurement. The second term is due to both the absolute center-frequency accuracy and the center-frequency stability of the time base and varies between multiple single-shot measurements over the observation interval (the amount of time from the first single-shot measurement to the final single-shot measurement).

Aux In (external) trigger channels

One channel

Aux In (external) trigger input impedance

1 MΩ ± 1% in parallel with 14 pF ± 3 pF

Aux In (external) trigger maximum input voltage

300 V_rms, Installation category II

Derate at 20 dB/decade above 3 MHz to 30 V_rms at 30 MHz; 10 dB/decade above 30 MHz.

Based upon a sinusoidal or DC input signal. The excursion above 300 V should be less than 100 ms in duration, and the duty factor is limited to < 44%. The RMS signal level must be limited to 300 V. If these values are exceeded, damage to the instrument may result.

Edge-type trigger sensitivity, DC-coupled

The greater of 2 mV or 0.4 div from DC to 20 MHz

The greater of 3 mV or 0.5 div from >20 MHz to 70 MHz

The greater of 4 mV or 0.5 div from >70 MHz to 100 MHz

The greater of 4 mV or 0.6 div from >100 MHz to 200 MHz

The greater of 5 mV or 0.7 div from >200 MHz to 350 MHz

The greater of 6 mV or 0.8 div from >350 MHz to instrument bandwidth

Edge trigger sensitivity, AC-coupled

The minimum sensitivities are as follows:

Trigger coupling	Typical sensitivity
AC	1.0 times the DC coupled limits for frequencies above 10 Hz. Attenuates signals below 10 Hz
NOISE REJ	2.5 times the DC coupled limits
HF REJ	1.0 times the DC coupled limits from DC to 50 kHz. Attenuates signals above 50 kHz
LF REJ	1.0 times the DC Coupled limits for frequencies above 50 kHz. Attenuates signals below 50 kHz

Trigger modes

Auto, normal, and single

Trigger coupling

DC, HF Reject (attenuates > 50 kHz), LF Reject (attenuates < 50 kHz), noise reject (reduces sensitivity)

Trigger level ranges

Any input channel

±5 divisions from center of screen

Aux In

±8 V

Trigger types

Edge

Positive, negative, or either slope on any channel.

Pulse Width

Trigger on width of positive or negative pulses. Event can be time- or logic-qualified.

Timeout

Trigger on an event which remains high, low, or either, for a specified time period. Event can be logic-qualified.

Runt

Trigger on a pulse that crosses one threshold but fails to cross a second threshold before crossing the first again. Event can be time- or logic-qualified.

Logic

Trigger when logic pattern goes true, goes false, or occurs coincident with a clock edge. Pattern (AND, OR, NAND, NOR) specified for all input channels defined as high, low, or don't care. Logic pattern going true can be time-qualified.

Setup/Hold

Trigger on violations of both setup time and hold time between clock and data present on any input channels.

Rise/Fall

Trigger on pulse edge rates that are faster or slower than specified. Slope may be positive, negative, or either. Event can be logic-qualified.

Parallel (with MSO option)

Trigger on a parallel bus data value. Parallel bus can be from 1 to 20 bits (from the digital and analog channels) in size. Supports binary and hex radices.

I2C (option)

Trigger on start, repeated start, stop, missing ack, address (7 or 10 bit), data, or address and data on I2C buses up to 10 Mb/s.

SPI (option)

Trigger on slave select, idle time, or data (1-16 words) on SPI buses up to 20 Mb/s.

RS-232/422/485/UART (option)

Trigger on start bit, end of packet, data, and parity error up to 15 Mb/s.

CAN (option)

Trigger on start of frame, type of frame (data, remote, error, or overload), identifier, data, identifier and data, end of frame, missing ack, and bit stuff error on CAN buses up to 1 Mb/s and CAN-FD buses up to 16 Mb/s.

LIN (option)

Trigger on sync, identifier, data, identifier and data, wakeup frame, sleep frame, and error on lin buses up to 1 Mb/s.

SENT (option)

Trigger on start of packet, fast channel status and data, slow channel message ID and data, and CRC errors.

Lowest frequency for successful operation of "Set level to 50%" function

50 Hz

Logic trigger minimum logic or rearm time

For logic, time between channels refers to the length of time a logic state derived from more than one channel must exist to be recognized. For events, the time is the minimum time between a main and delayed event that will be recognized if more than one channel is used.

For all vertical settings, the minimums are:

Triggering type	Pulse width	Rearm time	Time between channels
Logic	Not applicble	2 ns	2 ns
Time qualified logic	4 ns	2 ns	2 ns

Setup/hold violation trigger, setup and hold time ranges

Input coupling on the clock and data channels must be the same.

For setup time, positive numbers mean a data transition before the clock.

For hold time, positive numbers mean a data transition after the clock edge.

Setup + hold time is the algebraic sum of the setup time and the hold time programmed by the user.

The limits are as follows:

Feature	Minimum	Maximum
Setup time	0 ns	20 s
Hold time	0 ns	20 s
Setup + hold time	400 ps	21 s

Minimum pulse width, rearm time, and transition time

For trigger class width and runt, pulse width refers to the width of the pulse being measured. Rearm time refers to the time between pulses.

For trigger class slew rate, pulse width refers to the delta time being measured. Rearm time refers to the time it takes the signal to cross the two trigger thresholds again.

For Slew rate triggering, the minimum transition time defined as the time signal spends between the two trigger threshold settings.

Pulse class	Minimum pulse width	Minimum rearm time
Runt	4 ns	2 s
Width	4 ns	2 ns + 5% of width upper limit setting
Slew rate	4 ns	8.5 ns + 5% of delta time setting

Rise/fall time trigger, delta time range

800 ps to 20 s

Pulse width, or time-qualified runt trigger time range

800 ps to 20 s

Trigger holdoff range

0 s minimum to 10 s maximum.

Hold off may not function correctly in sequence trigger mode.

Digital input channels

16 Digital Inputs [D0:D15]

Input resistance, typical

101 KΩ to ground

Input capacitance, typical

8 pF

Specified at the input to the P6316 probe with all 8 ground inputs connected to the user's ground. Use of leadsets, grabber clips, ground extenders, or other connection accessories may compromise this specification.

Minimum input signal swing, typical

500mV peak-to-peak

Specified at the input to the P6316 probe with all 8 ground inputs connected to the user's ground. Use of leadsets, grabber clips, ground extenders, or other connection accessories may compromise this specification.

Maximum input signal swing, typical

+30 V, -20 V

DC input voltage range

+30 V, -20 V

Maximum input dynamic range

50 V_pp (threshold setting dependent)

Channel to channel skew (typical)

500 ps

Digital Channel to Digital Channel only

This is the propagation path skew, and ignores skew contributions due to bandpass distortion, threshold inaccuracies (see Threshold Accuracy), and sample binning (see Digital Channel Timing Resolution).

Thresholds

Thresholds per set of 8 channels

Threshold Selections

TTL, CMOS, ECL, PECL, User-Defined

Threshold voltage range

–15 V to +25 V

Digital channel timing resolution

Minimum: 2 ns

✔ Threshold accuracy

± [180 mV + 2% of threshold setting after calibration]. Requires valid SPC.

Minimum detectable pulse

5.0 ns

Specified at the input to the P6316 probe with all eight ground inputs connected to the user's ground. Use of lead sets, grabber clips, ground extenders, or other connection accessories may compromise this specification.

Operating modes

Continuous, burst

Function types

Arbitrary, sine, square, pulse, ramp, DC level, Gaussian, Lorentz, exponential rise/fall, sin(x)/x, random noise, Haversine, and Cardiac.

Amplitude and frequency range

Values are peak-to-peak voltages.

Waveform	Amplitude range 50 Ω	Amplitude range 1 MΩ	Frequency range
Arbitrary	10 mV to 2.5 V	20 mV to 5 V	0.1 Hz to 25 MHz
Sine	10 mV to 2.5 V	20 mV to 5 V	0.1 Hz to 50 MHz
Square	10 mV to 2.5 V	20 mV to 5 V	0.1 Hz to 20 MHz
Pulse	10 mV to 2.5 V	20 mV to 5 V	0.1 Hz to 20 MHz
Ramp	10 mV to 2.5 V	20 mV to 5 V	0.1 Hz to 500 KHz
DC Level		20 mV to 5V
Gaussian	10 mV to 1.25 V	20 mV to 2.5 V	0.1 Hz to 5 MHz
Lorentz	10 mV to 1.2 V	20 mV to 2.4 V	0.1 Hz to 5 MHz
Exponential rise	10 mV to 1.25 V	20 mV to 2.5 V	0.1 Hz to 5 MHz
Exponential decay	10 mV to 1.25 V	20 mV to 2.5 V	0.1 Hz to 5 MHz
Sin(X)/X	10 mV to 1.5 V	20 mV to 3.0 V	0.1 Hz to 2 MHz
Random noise	10 mV to 2.5 V	20 mV to 5 V
Haversine	10 mV to 1.25 V	20 mV to 2.5 V	0.1 Hz to 5 MHz
Cardiac	10 mV to 2.5 V	20 mV to 5 V	0.1 Hz to 500 KHz

Maximum sample rate

250 MS/s

Arbitrary function length

128 K sample

Sine waveform

Frequency setting resolution

0.1 Hz

Amplitude flatness

±0.5 dB at 1 kHz

±1.5 dB at 1 kHz for <20 mV_pp amplitudes with 50 Ω termination

Total harmonic distortion

1% into 50 Ω for amplitude > 100 mV

Spurious-free dynamic range

40 dB (V_pp ≥ 0.1 V) 50 Ω load

Square and pulse waveform

Frequency setting resolution

0.1 Hz

Duty cycle range

10% - 90% or 10 ns minimum pulse, whichever is larger

Minimum pulse time applies to both on and off time, so maximum duty cycle will be reduced at higher frequencies to maintain 10 ns of off time.

Minimum pulse width, typical

10 ns. This is the minimum time for either on or off duration.

Rise/fall time

5.5 ns, 10% - 90% with 50 Ω termination

Pulse width resolution

100 ps

Overshoot

<5% for signal steps > 100 mV_pp and frequency settings ≥100 kHz with 50 Ω termination

<7% for signal steps > 100 mV_pp and frequency settings < 100 kHz with 50 Ω termination

This applies to the overshoot of the positive-going transition (+overshoot) and the negative-going (-overshoot) transition.

Asymmetry

± 1% ± 5 ns, at 50% duty cycle with 50 Ω termination

Jitter

<500 ps TIE_rms

<60 ps TIE_rms, ≥100 mV_pp amplitude, 40% - 60% duty cycle (Square and pulse waveforms, 5 GHz measurement bandwidth)

Ramp and triangle waveform

Frequency setting resolution

0.1 Hz

Variable symmetry

0% - 100%

Symmetry resolution

0.1%

DC level range

±2.5 V into Hi-Z

±1.25 V into 50 Ω

Random noise amplitude range

20 mV_pp to 5 V_pp in to Hi-Z

10 mV_pp to 2.5 V_pp into 50 Ω

For both isolated noise signal and additive noise signal. Additive noise is 0% to 100% of the peak-to-peak amplitude specified. The additive noise range is restricted in favor of amplitude in order not to exceed the maximum output limits. There is currently a linear reduction from 100% to 0% above 50% amplitude.

Sine and ramp frequency accuracy

130 ppm (frequency ≤10 kHz); 50 ppm (frequency > 10 kHz)

Square and pulse frequency accuracy

130 ppm (frequency ≤10 kHz); 50 ppm (frequency > 10 kHz)

Signal amplitude resolution

500 μV (50 Ω)

1 mV (Hi-Z)

Signal amplitude accuracy

±[ (1.5% of peak-to-peak amplitude setting) + (1.5% of absolute DC offset setting) + 1 mV ] (frequency = 1 kHz)

DC offset Range

±2.5 V into Hi-Z

±1.25 V into 50 Ω

DC offset Resolution

500 μV (50 Ω)

1 mV (Hi-Z)

✔ DC offset accuracy

± [ (1.5% of absolute offset voltage setting) + 1 mV ]

Add 3 mV of uncertainty per 10 °C change from 25 °C ambient

Guaranteed, specification valid after 30 minute warm-up and Signal Path Compensation (SPC) at ambient.

Host processor

Application processing unit: Dual-core Arm Cortex-A53 MPCore with CoreSight; NEON and single/double precision floating point; 32 KB/32 KB L1 cache, 1 MB L2 cache

Real-time processing unit Dual-core Arm Cortex-R5F with CoreSight; single/double precision floating point; 32 KB/32 KB L1 cache, and TCM

Display type

Display area – 217 mm x 135 mm, TFT active matrix, and Liquid Crystal Display (LCD) with capacitive touch.

Display resolution

1,280 horizontal × 800 vertical pixels

Display modes

Overlay and stacked

Luminance

260 cd/m²

Display luminance is specified for a new display set at full white brightness.

Color support

16,777,216 (8-bit RGB) colors

Zoom

Horizontal and vertical zooming is supported in all waveform and plot views

Interpolation

Sin(x)/x and linear

Waveform styles

Vectors, dots, variable persistence, and infinite persistence

Graticules

Movable and fixed graticules, selectable between grid, time, full, and none

Color palettes

Normal and inverted for screen captures

Individual waveform colors are user-selectable

Format

YT, XY

Language support

English, Japanese, Simplified Chinese, Traditional Chinese, French, German, Italian, Spanish, Portuguese, Russian, Korean

USB interface

Two USB 2.0 high speed host ports on the side of the instrument

One USB 2.0 high speed device port on the side of the instrument (USBTMC support)

Ethernet Interface

One 8-pin RJ-45 connector that supports 10/100 Mb/s and 1000 Mbps Ethernet (in full duplex mode only)

Probe compensator, output voltage and frequency

Characteristic	Value
Output voltage	Normal: 0-2.5 V amplitude
Source impedance	Normal: 1 kΩ
Frequency	1 kHz

Auxiliary output (Aux out)

Aux out connector and functional modes

A single BNC connector

Acquisition (main) trigger out and AFG out

Aux out output voltage

Non-AFG voltage thresholds are listed in the following table:

Characteristic	Limits
Vout (HI)	≥ 2.5 V open circuit; ≥ 1.0 V into a 50 Ω load to ground
Vout (LO)	≤ 0.7 V into a load of ≤ 4 mA; ≤ 0.25 V into a 50 Ω load to ground

Aux input

300 Vrms CAT II with peaks ≤ ±425 V

Security lock

Rear-panel security slot connects to standard Kensington-style lock

VESA mount

Standard (VESA MIS-D 100) 100 mm x 100 mm VESA mounting points on rear of instrument

Ground lug

Provides a safe ground return path when the instrument is operating on battery

Real-time clock

A programmable clock maintains and reports the current time in the units of years, months, days, hours, minutes, and seconds.

Non-volatile memory capacity

One eMMC device (limited to 2 GB of usable space in SLC mode) contains the bootloader, operating system, application software, calibration constants, and user data storage.

Mass storage device capacity

Linux: ≥4 GB.

The form factor is an embedded eMMC BGA. It provides storage for saved customer data, all calibration constants and the Linux operating system. Not customer serviceable. Partition on the user device, with a nominal capacity of 2 GB, is available for the storage of saved customer data.

The physical capacity is larger, but in SLC mode it is 2 GB only for the longevity of the NAND flash.

Power consumption

60 W maximum

Source voltage

100 – 240 VAC ±10% (50/60 Hz)

Source frequency

50 – 60 Hz (100 – 240 VAC)

AC Adapter output

24 V DC, 2.71 A

Fuse rating

T3.15 A, 250 V

The fuse is not customer replaceable.

The line lead is fused, but the neutral lead is not fused.

Battery

Description

Requires Opt 2-BATPK or 2-BP battery pack, with 2 slots for batteries

Supports up to 2 TEKBAT-01 Li-Ion rechargeable batteries

Cell chemistry

Li-lon

Nominal capacity

6700 mAh

Voltage

14.52 VDC

Weight

450 g (1 lb)

Battery operating time, typical

Up to 4 hours with single battery

Up to 8 hours with dual batteries

Hot swappable

Battery life is measured under following conditions:

• Only one channel is turned on
• Lowest timebase setting selected
• Lowest record length is selected
• Fastest sample rate is selected
• All analysis or interpolation capabilities are turned off
• Edge trigger is selected
• Back-light set to low

Safety certification

The following certifications and compliance are applicable:

UL/CSA/EN 61010-2-030.

US NRTL Listed - UL61010-1.

Canadian Certification - CAN/CSA-C22.2 No. 61010.1.

EU Compliance – Low Voltage Directive 2014-35-EU and EN61010-1.

International Compliance – IEC 61010-1.

Pollution degree

Pollution degree 2, indoor, and dry locations use only.

Weight

Instrument only

1.8 kg (4 lbs)

Instrument with battery pack

3.2 kg (7 lbs) – one battery

3.6 kg (8 lbs) – two batteries

Instrument only dimensions

Height

210 mm (8.26 in)

Width

344 mm (13.54 in)

Depth

40.4 mm (1.59 in)

Instrument with battery pack dimensions

Height

210 mm (8.26 in)

Width

344 mm (13.54 in)

Depth

78 mm (3.07 in)

Clearance requirements

The clearance requirement for adequate cooling is 13 mm (0.5 in) on the rear of the instrument along the bottom edge (inlet vents) and top edge (exhaust vents).

Rackmount configuration

5U

Regional certifications, classifications, and standards list

European union

EC Council EMC Directive 2014/30/EU

Demonstrated using:

EN 61326-2-1:2006 Electrical equipment for measurement, control, and laboratory, part 2-1. Emissions that exceed the levels required by this standard may occur when this equipment is connected to a test object. Compliance is demonstrated using high-quality, shielded interface cables.

EN IEC 61326-1:2021 and EN IEC 61326-2-1:2021 EMC requirements for Class A electrical equipment.

Emissions:

EN 55011, Class A

Immunity:

IEC 61000-4-2

IEC 61000-4-3

IEC 61000-4-4

IEC 61000-4-5

IEC 61000-4-6

IEC 61000-4-11

EN 61000-3-2

EN 61000-3-3

Australia

EMC Framework, demonstrated per emission standard CISPR 11 in accordance with EN 61326-2-1.

United Kingdom

Electromagnetic Compatibility Regulations 2016-UK SI 2016 No.1091

Demonstrated using:

EN 61326-2-1:2013 Electrical equipment for measurement, control, and laboratory, Part 2-1. Emissions that exceed the levels required by this standard may occur when this equipment is connected to a test object. Use high quality shielded cables to maintain compliance.

Emissions:

EN 55011, Class A

Immunity:

IEC 61000-4-2

IEC 61000-4-3

IEC 61000-4-4

IEC 61000-4-5

IEC 61000-4-6

IEC 61000-4-11

EN 61000-3-2

EN 61000-3-3

Ukraine

Technical Regulations on Electromagnetic Equipment Compatibility TR 1077

DSTU EN 61326-1: 2016 (EN 61326-1: 2013. IDT) and DSTU EN 61326-2-1: 2016 (EN 61326-2-1: 2013. IDT): Electrical equipment for measuring control and laboratory use. Requirements for electromagnetic compatibility Part 1 consists of general requirements, and Part 2-1 consists of additional requirements. Test configurations, working conditions, and quality criteria for the operation of an accurate test.

Emissions:

DSTU EN 55011: 2019 (EN 55011: 2009. IDT. CISPR 11: 2009. MOD) / Amendment № 1: 2019 (EN 55011: 2009 / A1: 2010. IDT.

CISPR 11: 2009 / A1: 2010. IDT) - Industrial equipment, scientific, and medical radio frequency. Characteristics of electromagnetic interference, norms, and methods of measurement.

Immunity

DSTU EN 61000-4-11: 2019 (EN 61000-4-11: 2004. IDT. IEC 61000-4-11: 2004. IDT) - Electromagnetic compatibility Part 4-11 consists of test and measurement methods. Tests for immunity to voltage dips, short-term interruptions, and voltage changes.

DSTU EN 61000-4-2: 2018 (EN 61000-4-2: 2009. IDT. IEC 61000-4-2: 2008. IDT) - Electromagnetic compatibility Part 4-2 consists of test and measurement methods. Tests for resistance to electrostatic discharges.

DSTU EN 61000-4-3: 2019 (EN 61000-4-3: 2006. IDT. IEC 61000-4-3: 2006. IDT) / Amendment № 2: 2019 (EN 61000-4-3: 2006 / A2: 2010 IDT IEC 61000-4-3: 2006 / A2: 2010 IDT) - Electromagnetic compatibility. Part 4-3. Test and measurement methods. Tests for immunity to radio frequency electromagnetic fields of radiation.

DSTU EN 61000-4-4: 2019 (EN 61000-4-4: 2012. IDT. IEC 61000-4-4: 2012. IDT) - Electromagnetic compatibility Part 4-4 consists of test methods for testing and measurement. Tests for susceptibility to electrical rapid transition processes or pulse packets.

DSTU EN 61000-4-5: 2019 (EN 61000-4-5: 2014. IDT. IEC 61000-4-5: 2014. IDT) - Electromagnetic compatibility Part 4-5 consists of test and measurement methods. Tests for immunity to voltage and current surges.

DSTU EN 61000-4-6: 2019 (EN 61000-4-6: 2014. IDT. IEC 61000-4-6: 2013. IDT) - Electromagnetic compatibility Part 4 consists of test and measurement methods. Tests for immunity to conductive perturbations induced by radio frequency fields

Emissions that exceed the levels required by this standard may occur when this equipment is connected to a test object.

Compliance demonstrated using high quality, shielded interface cables.

Korea

EC Council EMC Directive 2014/30/EU

Demonstrated using:

EN 61326-2-1:2013 Electrical equipment for measurement, control, and laboratory, Part 2-1. Emissions that exceed the levels required by this standard may occur when this equipment is connected to a test object. Use high quality shielded cables to maintain compliance.

EN IEC 61326-1:2021 and EN IEC 61326-2-1:2021 EMC Requirements for Class A electrical equipment

Emissions

EN 55011, Class A

Immunity

IEC 61000-4-2

IEC 61000-4-3

IEC 61000-4-4

IEC 61000-4-5

IEC 61000-4-6

IEC 61000-4-11

EN 61000-3-2

EN 61000-3-3

Immunity

Electrostatic discharge (ESD), and enclosure port

IEC 61000-4-2

Radiated radio frequency electromagnetic field, and enclosure port

IEC 61000-4-3

Triggering when the trigger threshold is offset by less than 4 minor divisions from ground reference is allowed.

Electrical fast Transient/burst, and common-mode

IEC 61000-4-4

Surge/electrical slow transient

IEC 61000-4-5

Conducted radio frequency

IEC 61000-4-6

Ambient fields may induce triggering when the trigger threshold is offset by less than 1 major division from ground reference.

Voltage dips and short interruptions, and AC power port

IEC 61000-4-11

Product recycling information and documentation

User information should include an explanation of the recycling mark and direct the customer to the appropriate resources for recycling the product via one of the following methods:

1. Operator manual boilerplate; or
2. Pack-in errata sheet (only use this method if manual has been finalized); or
3. Online help file (if no other documentation is shipped with the product).

Temperature

Operating

0 °C to +50 °C (+32 °F to 120 °F)

Operating battery

0 °C to 45 °C (+32 °F to 113 °F)

Non-operating

-20 °C to +60 °C (-4 °F to 140 °F)

Humidity

Operating

5% to 90% relative humidity at temperatures up to +30 °C,

5% to 60% relative humidity at temperatures greater than +30 °C and up to +50 °C

Non-operating

5% to 90% relative humidity at temperatures up to +30 °C

5% to 60% relative humidity at temperatures greater than +30 °C and up to +60 °C

Altitude

Operating

Up to 3,000 meters (9,842 feet)

Non-operating

Up to 12,000 meters (39,370 feet)

EMC

Conforms to European Union EMC Directive (CE-marked)

Safety

Conforms to European Union Low Voltage Directive (CE-marked)

Conforms to ANSI/UL61010-1 and ANSI/UL61010-2-030 (CSA-marked)

Certified to CAN/CSA C22.2 No.61010-1 and CAN/CSA C22.2 No.61010-2-030 (CSA-marked)

RoHS

Conforms to European Union Restrictions on Hazardous Substances (CE-marked)

DC Gain Accuracy test record

Analog Bandwidth test record

Digital threshold accuracy tests with 2-MSO option

Long term sample rate test records

AFG DC Offset Accuracy Tests